P2T process positioned for recycling

British company Prodrive Composites (Milton Keynes, UK) recently issued a press release about a process, called P2T (Primary to Tertiary), for manufacturing recyclable composite components that can satisfy future end-of-life requirements without any compromise in performance. 
#regulation #sustainability #autoclave


Facebook Share Icon LinkedIn Share Icon Twitter Share Icon Share by EMail icon Print Icon

British company Prodrive Composites (Milton Keynes, UK) is known for design and manufacture of advanced lightweight structural and non-structural composites for a wide range of applications across the automotive, motorsport, aerospace, marine, defense and other sectors. It is the first UK composites business certified to IATF 16949 (an international standard for quality management defining the requirements of a quality management system for organizations in the automotive industry) and is leading the development of some innovative manufacturing processes including the application of graphene into structural composites.

The company recently issued a press release about a process for manufacturing recyclable composite components that can satisfy future end-of-life requirements without any compromise in the performance of the original parts. Called P2T (Primary to Tertiary), the process not only simplifies recycling, but endows a composite material with the potential to fulfill three or more useful lifetimes. John McQuilliam, chief engineer, Prodrive Composites answered some questions that CW posed about the P2T process.

The process uses a reactive thermoplastic resin instead of thermoset materials and reacts the plastic monomer with a catalyst in the presence of the reinforcement material to produce a cured laminate, out of the autoclave. The reactive thermoplastic may be like Arkema’s ELIUM resin, although McQuilliam  would not confirm the resin source. He did tell CW that there is no need to heat the monomer or catalyst, and that applied vacuum is used for the process, without autoclave or press. As shown in the company’s video, the process employs recycled carbon fiber mat from ELG Carbon Fibre Ltd.

According to Prodrive Composites, because the process doesn’t require an autoclave, costs are reduced so that production can be scaled up without major investment. Prodrive believes it is the first to develop this technique, which emerged through a development program with an automotive OEM customer who required a high-performance structural material with lower environmental impact than conventional composites.

“End-of-life recycling is one of the biggest debates in the composites world today,” explains McQuilliam. “The issue affects automotive manufacturers and wider industries too, such as marine, where old fiberglass boats are often broken up and sent to landfill. The main barrier to recycling has been the type of resin used; thermosetting resins predominate but these cannot be readily recycled.” He adds that thermosets were highly convenient materials to support the composites supply chain but, as tighter end-of-life regulations are introduced, better alternatives are required.

Composites produced by the P2T process can be recycled multiple times. The highest mechanical properties are obtained during first use of virgin fibers, enabling highly loaded structural items such as suspension wishbones to be manufactured. At the part’s end-of-life, the fibers and much of the resin can be recycled by chemical or thermal depolymerization, by heating the polymerized reactive thermoplastic to above its melting point to break the chains and reusing the now depolymerized material as raw material for a secondary part, such as a body panel. When the secondary part reaches the end of its life, it can be chopped and remolded into block material with properties suitable for 3D solid components. This tertiary part can itself be recycled several times until, finally, just the re-melted resin is recovered while the fibres are milled to supply other, lower grade parts.

McQuilliam tells CW that the polymerization process occurs at room temperature and that parts are intended for nominally ambient temperature use; no issues with heat distortion have been observed: “As with all composites, in-plane properties are dominated by the reinforcement and we have measured an improvement in through-thickness strength compared to epoxy resin.”

In addition to hand layup of parts, the P2T process is also compatible with advanced techniques, such as Tailored Fibre Placement (TFP). TFP makes more efficient use of the fibres than a conventional weave and is highly complementary to the P2T approach to recycling.

“This is a really exciting development which finally addresses the recycling challenges faced by composites,” concludes McQuilliam. “We have developed and refined the process and could bring new customer applications into series production within as little as twelve months.”

Watch the video to see the process: 



  • Composites 101: Fibers and resins

    Compared to legacy materials like steel, aluminum, iron and titanium, composites are still coming of age, and only just now are being better understood by design and manufacturing engineers. However, composites’ physical properties — combined with unbeatable light weight — make them undeniably attractive. 

  • Colored carbon fiber

    Options for adding color have been around for decades, but new products are hoping to up the ante and open new markets.

  • Recycled carbon fiber update: Closing the CFRP lifecycle loop

    Commercial production of recycled carbon fiber currently outpaces applications for it, but materials characterization and new technology demonstrations promise to close the gap.