Airtech
Published

Autocomposites and the myth of $5/lb carbon fiber

The $5/lb line in the sand comes with a similar challenge that, ultimately, will determine the fate of carbon fiber in automotive: Manufacturability.

Share

When I started this job in September 2006, one of the first “composites truths” handed down to me from on high was this: Carbon fiber will not be applied to high-volume automotive structures until and unless the unit cost of said carbon fiber drops to or below US$5/lb. And if you ask any 10 composites industry veterans what the origin of this “truth” was, you will almost certainly get 10 different answers, ranging from the plausible — “Ford Motor Co. said it in a meeting with material suppliers in 1988” — to the fantastic — “It was Richard Nixon’s deathbed proclamation.” (OK, I made that second one up, but you get the point.)

Anyhow, regardless of the genesis of this statement, it has been repeated so frequently in the ensuing years that it has assumed the veneer and polish of fact, often pulled out and pointed to by automotive OEMs whenever the composites industry gets to feeling a little uppity about making automotive inroads. And then we are politely reminded of our place in the materials food chain: “Now remember, little fella,” say the OEMs, “we’re used to affordable steel. We can’t use none of that new-fangled carbon fiber unless it’s super-cheap! But if you get the price down to $5/lb — oh boy! at would be something! Now run along ....”

And then, a funny thing happened: Carbon fiber got cheaper. How cheap? It’s hard to say. Carbon fiber manufacturers don’t publish their prices, but some casual inquiries revealed that 50K tow, industrial-grade carbon fiber can be acquired from one or more suppliers for as little as $7-$8/lb (€15.4-€17.6/kg). This is not $5/lb (yet), but it is also not $12 or $15/lb. And given this downward trajectory, plus the ongoing research into low-cost carbon fiber at Oak Ridge National Laboratory (ORNL, Oak Ridge, TN, US), it’s not unreasonable to think that this infamous threshold might be breached soon. And then, oh boy!

Maybe.

The truth of the $5/lb truth, however, is more complex than it appears. The true truth is that even if carbon fiber were offered to automakers for $0/lb, its use in high-volume automotive structures would not be a foregone conclusion. This is because the $5/lb line in the sand comes with a similar challenge that, ultimately, will determine the fate of carbon fiber in automotive: Manufacturability.

The real Achilles heel of carbon fiber composites manufacturing is that it’s not easy — at least not easy the way metal stamping and plastic injection molding are. It’s not easy to design, not easy to simulate and not easy to manufacture. Carbon fiber composites manufacturing means coping with a far greater number of variables, each of which must be anticipated, measured and then controlled. To top it off, composites are the only materials in the world that are made at the same time as the parts they make.

This isn’t to say that it’s not getting easier, because it is. And in the automotive industry, fabrication of carbon fiber structures is focusing on molding processes that mimic legacy metalforming processes: Compression molding, injection overmolding and resin transfer molding show great promise for high-volume autocomposites manufacture, but to activate the value of that still-mythical $5/lb carbon fiber, they must meet automotive supply chain cycle time, repeatability, process control and waste requirements. And of these, the most important might be waste. Composite parts, no matter how inexpensive carbon fiber becomes, will always have 
a relatively large material cost burden, thus material use must be fully optimized to make carbon fiber viable.

So, the real question for automotive OEMs is not, How cheap do you want your carbon fiber to be? Rather, the question is, What is your cost target per kilogram of part weight? I await the answer from on high — or you. Email me at jeff@compositesworld.com with your “true” number.

cut by an Eastman
Carbon Fiber 2024
Sysenqo high performance materials
Keyland Polymer
Airtech
NewStar Adhesives - Nautical Adhesives
CompositesWorld
Thermwood Corp.
Chem Trend
HEATCON Composite Systems
KraussMaffei Metering Systems
industrial CNC routers

Related Content

Hi-Temp Resins

Price, performance, protection: EV battery enclosures, Part 1

Composite technologies are growing in use as suppliers continue efforts to meet more demanding requirements for EV battery enclosures.  

Read More

CFRTP enables better, greener smartphones

Carbon Mobile’s “monocoque” design eliminates separate case, cover and frame, better protects electronics and simplifies disassembly.

Read More
Natural Fibers

Thermoset-thermoplastic joining, natural fibers enable sustainability-focused brake cover

Award-winning motorcycle brake disc cover showcases potential for KTM Technologies’ Conexus joining technology and flax fiber composites.

Read More
Epoxies

TU Munich develops cuboidal conformable tanks using carbon fiber composites for increased hydrogen storage

Flat tank enabling standard platform for BEV and FCEV uses thermoplastic and thermoset composites, overwrapped skeleton design in pursuit of 25% more H2 storage.

Read More

Read Next

Thermoplastics

From the CW Archives: The tale of the thermoplastic cryotank

In 2006, guest columnist Bob Hartunian related the story of his efforts two decades prior, while at McDonnell Douglas, to develop a thermoplastic composite crytank for hydrogen storage. He learned a lot of lessons.

Read More
Wind/Energy

Composites end markets: Energy (2024)

Composites are used widely in oil/gas, wind and other renewable energy applications. Despite market challenges, growth potential and innovation for composites continue.

Read More
Trends

CW’s 2024 Top Shops survey offers new approach to benchmarking

Respondents that complete the survey by April 30, 2024, have the chance to be recognized as an honoree.

Read More
Kraussmaffei Metering Systems