Are high-temperature thermoset resins ready to go commercial?
Developed for the U.S. military, these high-performance matrices are branching out into wider use.
By Sara Black, Technical Editor | November 2004
While reinforced ceramic and metal matrix composites have the ability to take extreme heat -- 1649°C/3000°F or more -- many designers prefer polymer resins to ceramics or metals because polymers perform better under fatigue than more brittle ceramics and are much lighter than most metals. Thanks to a long series of military and aerospace research projects, an array of thermoset resins have been developed to handle moderate-to-high temperatures and tough conditions with ease -- providing weight savings and lower life-cycle costs into the bargain. While most of these materials have been around for decades, some new variations and end-uses are emerging for situations where no other materials can do the job. And the advent of new nanocomposites promise some improvements, as well.
Source: Dassault Aviation, F. Robineau
The Dassault Rafale fighter jet incorporates high-temperature cyanate ester resin in its composite wing structure.
"All of these materials have their place," says NASA's John Connell, a high-temperature polymer expert and a member of the steering committee for the "High Temple" workshop symposium sponsored each year in the U.S. by NASA and the U.S. Air Force Research Laboratory (AFRL) for high-temperature resins. "It's a matter of finding the best combination of processing and performance characteristics for the end-use," he says, adding, "Of course, cost of the final component is a major consideration."
The formidable range of available polymers includes several types of polyimides; cyanate esters, bismaleimides, benzoxazines, phthalonitriles and phenolics, as well as new nanocomposite-enhanced resins. HPC takes a brief look at some of the history, chemistry, issues and end uses of these high-performance materials.
Polyimides
"Traditional linear polyimides have a high melt viscosity that limits processability and, consequently, end-use," explains Connell. "By lowering the molecular weight and using reactive endcapping agents to produce thermosetting polyimides, the processability has been improved."
Source: NASA
PETI polyimide resins commercialized by UBE America provide high-temperature performance and can be used in resin transfer molding processes.
Thermosetting polyimides, originally developed in the 1970s at NASA Lewis for military aircraft engines and airframes, are produced by dissolving an aromatic diamine, a dialkyl ester of tetraxarboxylic acid and a monofunctional nadic ester endcapping agent in a solvent, such as alcohol. The resulting solution is typically used to produce prepreg. PMR-15 is the best known of these thermosetting formulations -- PMR is shorthand for in-situ polymerization of monomer reactants -- and it is "very successful" in producing good thermal and mechanical properties, says Dr. Ruth Pater, a senior polymer scientist at NASA's Langley Research Center.
But, while PMR-15 and similar variants have good mechanical properties, they contain the hazardous compound methylenedianiline (MDA), creating a potential health and safety issue. NASA encouraged research to develop new versions, using less-toxic monomers, and several have emerged. Pater was directly involved in the development of RP-46, patented in 1991, a direct PMR-15 replacement with very similar chemistry. Unitech Corp. (Wake Forest, N.C., U.S.A.) is one of two licensees of the RP-46 resin technology.
Because of its high degree of crosslinking, a carbon fiber/RP-46 composite has a glass transition temperature (Tg) of 397°C/747°F and sustained service temperature is 357°C/675°F. Unitech chemist Perlita Razon says tests show that short-duration spikes to 815°C/1500°F can occur without resin breakdown. RP-46's thermoxidative stability is very high, meaning it resists oxidation (combustion) that breaks down molecular bonds and causes weight loss and structural decline, even at very high temperature. Flexural strength is 71 ksi at 343°C/650°F under hot/wet conditions. Their high crosslink densities also make polyimides fairly brittle, and microcracking under repeated heat cycles can occur, although in many applications, it isn't an issue.
RP-46, like PMR-15, cures with a condensation reaction, meaning that water and alcohol are evolved and given off from the polymer chain during cure. NASA's Connell says that the volatiles can be dealt with by designing the cure cycle with specific ramp-ups and holds at different temperatures, to ensure the volatiles are driven out of the part to eliminate voids. AFRL's Dr. Katie Thorp adds that the cure has to be designed so that the moisture evolution occurs before the crosslinking step, for best results.
In addition, a downside to older-style polyimides is their tendency to absorb moisture after cure. According to Connell, the newer polyimides have licked that problem to a large degree, with most absorbing less than one percent. Unitech cites data of 0.62 percent weight gain due to moisture absorption for a unidirectional carbon/RP-46 composite after 30 days at 85°C/185°F and 85 percent relative humidity.
The PMR chemistry with solvents and volatile evolution means that most processing to date has been limited to prepreg-based methods, although lower-viscosity versions are available, which are more suited to dry reinforcements and closed molding processes. Razon says Unitech is working on a new version of its resin that can be used in lower cost infusion processes. Another processing concern is that reaction time is fairly short and high cure temperature and pressure -- 325°C/617°F and 200 psi -- are needed, which may necessitate specialized autoclave or press equipment for some manufacturers.
YLA Advanced Composite Materials (Benicia, Calif., U.S.A.) does 90 percent of Unitech's prepregging, for customers that want prepregs for their applications. Several proprietary products are being produced with RP-46, including a high-temperature bearing for a commercial aircraft engine and a radome application. "RP-46 has excellent dielectric properties," states Razon, which was a major reason for its selection by the radome manufacturer. Quartz fiber/RP-46 woven prepreg cloth is hand layed up on composite tooling and the parts are autoclave-cured. Razon says that, at the speed the part travels, it sees 371°C/700°F temperatures for three to four minutes and spikes of 538°C/1000°F for approximately 30 seconds at a time, all easily within the part's performance specifications.
More polyimides and variants
An example of a successfully commercialized PMR- type polyimide is Goodrich Corp.'s (Stow, Ohio, U.S.A) SuperImide polyimide. The resin system, with chemistry based on high levels of aromaticity, was developed in the early 1990s by Goodrich as a "family" of resins with tailorable performance characteristics. Commercialization occurred in 2000 and since that time, over 1 million fabricated components have been produced for aircraft brake and jet engine applications. Several versions of SuperImide are currently available. Goodrich does not offer the raw material commercially, but is an exclusive supplier of finished, engineered components, per customer design requirements.
SuperImide resin-based components provide high levels of thermoxidative stability, withstanding continuous operating temperatures in excess of 343IntC/650IntF. For applications where thermal spikes are encountered, Goodrich maintains that SuperImide components can readily withstand repetitive thermal spike temperatures greater than 537IntC/1000IntF.
Other second-generation, non-MDA containing polyimides include those commercialized by Maverick Corp. (Blue Ash, Ohio, U.S.A.). (Maverick also sells traditional, military-qualified but MDA-containing MVK-19, PMRII-50 and AFR700 polyimides.) The Maverick resin was developed through a small business innovation research (SBIR) grant, in conjunction with NASA Glenn Research Center, with lower cost infusion molding in mind, according to the company. Using solvent-assisted resin transfer molding (RTM), complexly shaped parts, like aircraft engine cooling tubes with use temperatures of 260°C/500°F, can be produced with braided reinforcement. Cured parts exhibit Tgs up to 335°C/635°F and good thermoxidative stability in aircraft engine environments.
For NASA's Connell, the focus has been on a different polyimide chemistry, termed phenylethynyl (PE), or sometimes referred to as PETI, for phenylethynyl terminated imide, a reference to the polymer chain's phenylethynyl "end caps." PETI resins came about because of the desire for a structural matrix resin that could provide higher temperature performance and longer-term thermoxidative stability than bismaleimides. Work was originally conducted under NASA's High Speed Civil Transport (HSCT) program and continued with Air Force, NASA and jet aircraft engine manufacturer funding, with high-temperature engine parts in mind, says Connell.
"We believe that developing an RTM-able form of a very high-temperature resin is a real breakthrough," he adds. Since the resin cures in an addition reaction without volatile evolution, void- and microcrack-free carbon/PETI demonstration parts have been produced with Tgs as high as 375°C/707°F, using a material identified as PETI-375. Another version, designated PETI-330, is being commercialized by UBE America (New York, N.Y., U.S.A.), with a Tg of 330°C/630°F and continuous use temperatures (>1000 hours) of 288°C/ 550°F. M & P Technologies Inc. (Marietta, Ga., U.S.A.) has used PETI-330 to produce complex parts with RTM, and flat laminates have been made with vacuum-assisted RTM (VARTM).
PETI-330 has been produced in 100 kg lots and is commercially available from UBE America, while PETI-375 is still in development. While these resins, designed for primary structural applications in airframes and jet engines, produce tough composites, they do cost more than PMR-type materials. Producing larger batches and addressing raw material costs will help, says Connell. UBE America spokesperson Stewart Bain adds, "These resins offer manufacturers an alternative, for one-step processing rather than multistep cure cycles. We're pleased with the test results so far and several customers are incorporating PETI resins into their products successfully."
BMIs and cyanate esters
BMIs are technically a type of polyimide, prepared from the reaction of maleic anhydride and a diamine. BMIs bridge the temperature performance gap between epoxies and the PMR polyimides described above. They exhibit epoxy-like processing characteristics, curing by an addition, rather than a condensation, reaction. Thus, they avoid the off-gassing characteristic of polyimides and have temperature performance intermediate between epoxy and polyimide, says Marcia Tucker product manager for BMIs at Hexcel (Casa Grande, Ariz., U.S.A.).
Brittleness also is an issue with traditional BMIs used in airframes, and resin suppliers are working to address this with thermoplastic or elastomeric fillers. Newer BMI versions have greatly improved toughness that meets or exceeds that of polyimides.
Hexcel's F655 resin is one BMI product that sacrifices a bit of temperature performance for enhanced toughness. F655's Tg in dry conditions is 288°C/550°F, and it exhibits excellent compression strength after impact. In addition to standard autoclave processing, Hexcel's BMI also can be processed via RTM methods. F655 resin is being used by The Nordam Group (Tulsa, Okla., U.S.A.) for the Gulfstream G-450 thrust reverser.
Cytec Engineered Materials Inc. (Tempe, Ariz., U.S.A.) is well known for its BMI resin products used in aerospace, as well as its extensive overall high-temperature materials portfolio. CYCOM-5250-4 is Cytec's best-known BMI product, which can be prepregged or used as an RTM resin. The resin has a dry Tg of 296°C/565°F, and RTM'd parts exhibit continuous service temperature resistance up to 204°C/400°F, with excellent toughness. Cytec's BMI resins have been used for years in F-22 fighter jet parts.
An industry source says that, in addition to its existing polyimide products, Cytec will soon begin offering a new high-performance polyimide resin originally developed by the Air Force. With no MDA, AFR-PE-4 has performance equivalent to PMR-15, with easier processing.
Cyanate esters are a high-temperature resin family traditionally associated with space applications, because of very low dielectric properties (i.e., the material is transparent to electromagnetic signals) and extremely low moisture uptake compared to other resins, particularly polyimide. William McCarvill of Commercial Chemistries LLC (Salt Lake City, Utah, U.S.A.) says cyanate ester is attractive because it combines low moisture uptake with temperature resistance sufficient to handle the extreme temperature swings in space. Any moisture absorbed during processing will outgas in space, which can affect the stability of the part, particularly if it has to measure or record sensitive data. Cyanate ester's lower moisture uptake means lower shrinkage during cure and substantially less outgassing, and it is more resistant to microcracking.
Downsides are insufficient toughness in lower cost versions, a lower temperature resistance than BMI in most cases and the need to protect the resin from moisture. According to YLA's director of marketing Sean Johnson, it is necessary to prevent exposure of the resin to water during progression of the cure reaction, through cure dwell cycles. Prudent housekeeping is recommended, he says. That includes controlling humidity, both in the resin storage area and processing area, and the use of packaging and desiccants.
Johnson points out that in bonding applications, cyanate esters are compatible with most other resin systems and can be formulated for prepreg, RTM, filament winding, towpreg, syntactic core and adhesive forms. While their cost is higher than epoxy and BMI -- as high as $125/lb (USD) -- many backbone formulations are available for tailored performance in a wide range of costs.
Cytec's cyanate ester products -- CYCOM 5245C and CYCOM 5575-2 -- are used for radome applications and in the wing of Dassault's Rafale fighter jet, says the company. Hexcel offers cyanate ester resins as well.
