Precision Board Urethane Tooling Board
Published

Future multifunctional structures: Composites needed

Barton Bennett (Odyssian Technology, South Bend, Ind.) discusses multifunctional systems that will soon integrate composite structures with sensors, mechanisms and subsystems.

Barton Bennett

Share

Multifunctional structure technology encompasses a vast array of technologies, including structural health monitoring, smart structures, morphing structures, adaptive structures, self-healing structures and a multitude of related technologies. All of these offer the common benefit of increasing system-level capability and efficiency by integrating structure with sensors, mechanisms and subsystems. Ongoing technological advances in miniaturization will stimulate a drive toward even greater levels of integration. Examples of miniaturization technologies include microelectromechanical systems (MEMS), nanocomposites and materials, micro-miniaturization of electronics, thin films, embedded passive electronics and solid state actuating materials. 

The U.S. military and the National Aeronautics and Space Admin. (NASA) have been, and continue to be, the primary force behind the development of multifunctional structure technologies, and have long recognized their benefits. Multifunctional composite structure was demonstrated on NASA’s New Millennium Program Deep Space 1 spacecraft, which was built by Lockheed Martin Astronautics (Denver, Colo.). Under this program, the multifunctional electronic structure, which included conventional flex circuitry, demonstrated an estimated 50 to 80 percent savings in mass and volume. Other platforms have demonstrated the benefits of multifunctional structure, including NASA’s EOS-1, the Boeing Co.’s (Chicago, Ill.) Delta IV ELV launch vehicle and the Global Hawk unmanned aerial system. Most of this work has focused on embedding lightweight circuits in composite structures to achieve mass reduction of more than 50 percent.

Structural health monitoring in future aircraft will allow for rapid damage detection, repair and redeployment. Conformal load-bearing antenna aerostructures will allow for improved detection and communication while maintaining desired stealth and aerodynamic performance. Looking forward, embedded low-profile actuators and modulus-changing material systems will allow for adaptive space and air vehicle structures that respond to changing environmental conditions, thus improving aerodynamic control and system survivability. Highly integrated or embedded electronics will reduce the weight and volume of future high-performance systems by eliminating support chassis, avionic/electronic racks, enclosures, brackets, clips and insulation/isolation materials. Reduced volume, in turn, will permit either a lower overall system size or an increase in available payload volume. Cost reduction will be achieved by eliminating the cost of design, production planning and control, and manufacturing associated with each part that is no longer required.

R&D is already underway on many fronts that will contribute to the realization of highly integrated and embedded subsystems for future space and aircraft structures. Enabling technologies that are required include new circuit design architectures with distributed redundancy, fast-acting thin-film switching, and structural gradient and tailored materials for force load control. Thin- and thick-film multilayer power and signal networks likely will be deeply embedded within a composite airframe structure near the neutral axis to minimize shear loads. The networks will transfer signal and power through the use of structural vias (z-axis conductors) that are designed to handle shear loads while minimizing degradation of in-plane strength in the composite structure. Thermal management of active, heat-generating components will be achieved through larger area circuitry and coupling to thermally conductive structural elements. High-speed communication will be realized by improving the performance of intrinsically conductive polymers and engineered electrically conductive polymer materials. Other areas of required research include neural network science, reconfigurable or self-healing structural power/communication networks, and high-performance actuating and morphing material systems and circuit devices that support adaptive structures and flight control. As these structurally integrated signal and power networks develop, they will offer great performance advantages and undoubtedly will be found in future spacecraft and high-performance aircraft, working together with composite structures.

For consumer products, miniaturization of electronic and mechanical components will help achieve smaller and smarter products. Integrating these miniaturized components into structures and housings will allow even greater weight/volume reductions with increased sophistication and functional capability. For example, some automakers have begun to embed sensors into automobile bumpers and side panels, which can enable the relay of collision data to emergency medical personnel. And, there are countless other applications: Sporting goods now in development will use multifunctional structures to improve athletic performance — something already possible in composite snow skis and tennis rackets that have embedded piezoelectric materials for vibration control. 

To reap the full benefit of this high pay-off technology trend, research must continue in multiple areas to develop and demonstrate adequate structural, thermal, signal-processing and networking performance. The close collaboration of those with expertise in composite materials will be essential to success.

Janicki employees laying up a carbon fiber part
Precision Board Urethane Tooling Board
Wickert Hydraulic Presses
Compression Molding
ViRTEK IRIS 3D
Composites One
Park Aerospace Corp.
CW Tech Days Sustainability - Register Today!
KraussMaffei Metering Systems
CompositesWorld
NewStar Adhesives - Nautical Adhesives
Thermwood Corp.

Related Content

Thermoplastic composites welding: Process control, certification, crack arresters and surface prep

More widespread use of welded composite structures within a decade? Yes, but further developments are needed.

Read More

Thermoset-thermoplastic joining, natural fibers enable sustainability-focused brake cover

Award-winning motorcycle brake disc cover showcases potential for KTM Technologies’ Conexus joining technology and flax fiber composites.

Read More
Focus on Design

3D-printed CFRP tools for serial production of composite landing flaps

GKN Aerospace Munich and CEAD develop printed tooling with short and continuous fiber that reduces cost and increases sustainability for composites production.

Read More
Autoclave

Materials & Processes: Tooling for composites

Composite parts are formed in molds, also known as tools. Tools can be made from virtually any material. The material type, shape and complexity depend upon the part and length of production run. Here's a short summary of the issues involved in electing and making tools.

Read More

Read Next

Pressure Vessels

Composites end markets: Energy (2024)

Composites are used widely in oil/gas, wind and other renewable energy applications. Despite market challenges, growth potential and innovation for composites continue.

Read More
Thermoplastics

From the CW Archives: The tale of the thermoplastic cryotank

In 2006, guest columnist Bob Hartunian related the story of his efforts two decades prior, while at McDonnell Douglas, to develop a thermoplastic composite crytank for hydrogen storage. He learned a lot of lessons.

Read More
Trends

CW’s 2024 Top Shops survey offers new approach to benchmarking

Respondents that complete the survey by April 30, 2024, have the chance to be recognized as an honoree.

Read More
Precision Board Urethane Tooling Board